Measurements and Instructions
- Card base Petal Pink 5 1/2” x 8 1/2”, scored at 4 1/4”
- 1st card layer Petal Pink 4 1/8” x 5 3/8”, embossed with Brick & Mortar 3D embossing folder
- 2nd card layer Very Vanilla 3 3/4” x 5”, also embossed with Brick & Mortar 3D embossing folder
- Card insert Very Vanilla 3 3/4” x 5”
- Scrap of Very Vanilla, Petal Pink and Gray Granite
- Scrap of Bronze foil
- Gumball Shaker Dome and Frosted Beads
Score card base and burnish fold.
Adhere 1st card layer directly to card front.
Die cut gumball machine parts from cardstock and foil.
Place die cuts on top of the Vanilla layer so you can see where you should die cut for the shaker dome. Remove the die cut pieces, place die on top of Very Vanilla layer and adhere with low-tack tape. Die cut and reserve the die cut piece.
Adhere shaker dome to the inside of the Very Vanilla layer. Turn the layer over and put Frosted Beads inside the dome. Then cover the backside of the dome with either the die cut that you reserved or a scrap piece of Very Vanilla.
Adhere the entire Very Vanilla layer with shaker dome directly onto the 1st card layer.
Finish assembling the gumball machine by adhering your die cuts directly onto the card front.
Stamp the sentiment, adhere tag. Adhere hearts (optional) and Very Vanilla Baker’s Twine.
Measurements and Instructions
- Card base Granny Apple Green 4 1/4” x 11”, scored at 1” and 6 1/4” on the long side
- 1st card layer Pattern Party DSP 4” x 4 1/2”
- Basic White cardstock (1)- 4” x 4 1/2” and (1)-3/4” x 4”
- 2 die cuts from Heart Punch Pack, (1) Granny Apple Green and (1) Pattern Party DSP
- About 10” Playful Pets Trim
This is a matchbook card.
Score and burnish card base.
Stamp sentiment on strip of Basic White. I used Granny Apple and Poppy Parade classic inks
Stamp inside of card as you like. I used Bermuda Bay, Granny Apple Green and Poppy Parade classic inks.
Adhere Basic White cardstock to inside. Adhere DSP and punched hearts to outside.
Staple the bottom of the Granny Apple Card base with 1 staple. Put your staple fairly low so that you have room to adhere your candy to the inside flap (I used glue dots for the candy). Cover up front of staple by adhering your Basic White stamped strip.
Wrap trim around fold and tie in a square knot.
Measurements and Instructions
- Card Base Pool Party 4 1/4” x 11”, scored at 5 1/2”
- 1st card layer Pattern Party DSP, 4” x 5 1/4”
- 2nd card layer Basic White cut with Stitched Rectangle die measuring 3” x 4 3/8”
- Small tag cut from Tailor Made Tags and modified to be shorter than the full die
- Scrap of Basic White
- About 5” Fan Baker’s Twine in Poppy Parade/White
Score and burnish card base.
Stamp gumball machine on Basic White rectangle, and stamp again on the scrap-you don’t need the entire image but be sure to stamp the middle part where the mechanism is. Color if you like - I used Real Red and Bronze Stampin’ Blends.
Stamp inside the globe of the machine. I stamped hearts in Bermuda Bay and colored to resemble glass with Light Pool Party Stampin’ Blend.
Fussy Cut bronze mechanism and pop up on stamped gumball machine.
Adhere entire Stitched Rectangle panel to front of card. I used Stampin’ Dimensionals.
Stamp sentiment on tag and adhere to image. Tie bow and adhere with glue dot.
Thanks for visiting The Stamping Zoo - please come back soon!
Comments
Post a Comment